Hi, folks
Is there anybody use IOS 12.0(7)S version?
We got PA-2T3+ card for Cisco 7507, and upgraded its software from 11.2P to
12.0(7)S.
After that, suddenly routing didn't work.
We use BGP for external connection and OSPF for internal connection.
But traffic from OSPF didn't go to outer Internet at all.
Is there any factors that I need to adjust?
We tried to traceroute from internal network to Cisco 7507, and it was
fine.
When we tried to traceroute from Cisco 7507 to outer Internet, it was fine.
But when we tried to traceroute from internnal network to outer Internet,
there was timeout at Cisco 7507.
When I use "sh ip route", it looks fine.
I don't know why.
Please let me know the reason or solution.
Thanks in advance.
Hyun
On a similar note, a few weeks ago I upgraded a 7206 from 11.1(25)CC to
11.1(28)CC hoping to use ip verify unicast reverse-path. 11.1(25)CC
crashed months ago when I tried that the first time. Supposedly it was
fixed in 28. A week after upgrading to 11.1(28)CC, one of our T3's on a
PA-T3 card started flapping somewhat regularly. We had the line
tested/monitored, and nothing was found. After about a week of that, I
downgraded back to 11.1(25)CC. It's been 8 days since the downgrade, and
no flaps yet. Is there stable code for the 7206 that supports the PA-T3,
PA-2T3, PA-MCT3, CEF, BGP, OSPF, and ip verify unicast reverse-path?
Also, we're considering upgrading that router to a 7206VXR and adding a
few more T3's to it. It already has 3 (2 fractional, 1 full). Is there
stable code for the VXR with support for the above? Is there 11.1CC code
that can be run on a VXR, or are we forced to use 12.0?
Hi,
We tried to use 12.0(7)S with (among others) a GEIP module. It worked (with
rudimentary routing), apart from that the interfaces didn't want to mount by
themselves, but needed a manual
"shut, no shut" 
Another Q : Anyone experienced problems going from 11.1(29)CC1 to 12.0(5)T1
? We've had the
following : the router (a 7513) hanging on boot over invalid configuration
statements :
no ip route-cache optimum (I guess it's an out-dated entry ?
Replacement ?)
and a
atm pvc x x x
related statement (I unfortunately doesn't have literally at hand at home) ?
Cheers
mh
Hi, folks
Is there anybody use IOS 12.0(7)S version?
We got PA-2T3+ card for Cisco 7507, and upgraded its software from 11.2P
to
12.0(7)S.
After that, suddenly routing didn't work.
We use BGP for external connection and OSPF for internal connection.
But traffic from OSPF didn't go to outer Internet at all.
Is there any factors that I need to adjust?
We tried to traceroute from internal network to Cisco 7507, and it was
fine.
When we tried to traceroute from Cisco 7507 to outer Internet, it was
fine.
We had a problem with 12.0(3) (I think it was) saving the wrong atm pvc
statements to startup-config which made it unable to bring up the pvcs on
boot. We just upgraded to 12.0(7) and it seems to work now. This was on a
7206.
Now we just need to figure out why the 7206 wont detect our POS cards we
just put in there 
Hi (or Hej ! ;),
> atm pvc x x x
>
> related statement (I unfortunately doesn't have literally at hand at
home) ?
We had a problem with 12.0(3) (I think it was) saving the wrong atm pvc
statements to startup-config which made it unable to bring up the pvcs on
boot
Something along the lines that we've experienced then. The routers hung on
boot
complaining over invalid config. statements.
We just upgraded to 12.0(7) and it seems to work now. This was on a
7206.
Ahh, the .S version. Seemingly OK for us (though not tested on the same -
production - box). There
was a problem, though... having to 'shut; no shut' the Gig Eth interfaces
manually.
Now we just need to figure out why the 7206 wont detect our POS cards we
just put in there
Will keep you updated on future tests.
Thanks
Michael